Outbound Dialer Calls End With No Buyer, or a Buyer Refuses the Call

Power Dialer

When the Power Dialer connects a lead to an agent and the agent can't find a buyer, or a buyer that looked available refuses the call, the cause is usually a buyer setting or the order the agent pressed the buyer buttons in. This article walks through the causes, most common first, so you can tell them apart from the call's log and your own settings.

A Ping Reply Cached for Longer Than the Bid Lasts

What you see: a buyer accepts the ping, then refuses the call when it is dialed, or the call's log shows the buyer's earlier reply instead of a new ping.

Where to check: open the buyer's Conversion Settings, edit the conversion criteria, and look at Seconds To Cache Successful Response. While that time runs, Trackdrive reuses the buyer's last successful reply instead of pinging again.

The fix: set the cache shorter than the time the buyer honors its bid for, or to zero if the buyer wants a new ping for every call.

Example: a buyer honors a bid for 30 seconds, but its reply is cached for 300 seconds. A second call four minutes later reuses the old reply, and the buyer refuses the transfer.

Reload Buyers Passes Over a Buyer Already Dialed

What you see: after a buyer declines, is busy, or doesn't answer, the agent presses Reload Buyers and that buyer is never offered again on this call, or the agent sees no buyer at all.

Where to check: in the Control Center, Reload Buyers offers the next matching buyer not yet dialed on this call. A buyer that declined, was busy or didn't answer counts as dialed, so Reload Buyers passes over it for the rest of the call. Reset Find A Buyer clears the call's list of dialed buyers, so the next Reload Buyers offers the top matching buyer again.

The fix: press Reset Find A Buyer, then Reload Buyers, when the agent wants to try a buyer that already refused this call. If the agent sees Find A Buyer instead of these two buttons, the agent's team lacks the Agent: Manually Refresh and Dial Buyer permission or the company lacks one of the two actions; see "How to Use the Agent Control Center".

Example: a buyer was busy on the first try. The agent presses Reload Buyers twice and gets the second and third buyers, then nothing. Reset Find A Buyer followed by Reload Buyers offers the first buyer again.

Dials Paced on Waiting Agents, Not on a Buyer's Free Seats

What you see: many outbound calls end with no buyer during busy hours, while the same buyers take calls at quieter times.

Where to check: the dialer places calls for agents who are waiting for a lead. It does not wait for a buyer to have a free seat, so when every matching buyer is at its concurrency cap or caps, the agent's call finds no buyer. Compare the number of agents on the schedule with the buyers' concurrency caps on their pages.

The fix: match the number of agents dialing to the buyer capacity you have, or add buyers for the hours when calls end with no buyer.

Example: ten agents dial for an offer whose two buyers take three live calls each. Once six calls are with buyers, the next agents' calls have no buyer to transfer to.

A Contact Field Filter That Is Not Checked Before Dialing

What you see: the agent reaches the lead, but no buyer matches, because the lead's state, zip code or another field fails a buyer's filter.

Where to check: on the offer's contact fields, a field is checked against buyers before a lead is dialed only when Check Buyer Filters Before Calling is selected for it. A field without it is checked only after the agent is talking to the lead.

The fix: select Check Buyer Filters Before Calling on each contact field your buyers filter on, so leads that no buyer accepts are not dialed.

Example: every buyer filters on state, but the state field is not checked before calling. Leads from states no buyer takes are dialed, and those calls end with no buyer.

Paused Buyers and Buyers Left Out of Prematch Search

What you see: a buyer you expect to take dialer calls never appears when the agent looks for a buyer, or the dialer never calls leads that only that buyer matches.

Where to check: on the buyer's page, a paused buyer takes no calls. Use With Prematch Search? decides whether the dialer counts the buyer as a match when it looks for leads to dial; when it is off, leads that only this buyer matches are not dialed.

The fix: unpause the buyer, and turn on Use With Prematch Search? for a buyer the dialer should dial leads for.

Example: a new buyer is the only one that takes leads from two states, but Use With Prematch Search? is off on its page. The dialer never calls leads from those states until it is turned on.

Agents Waiting on a Screening Flow

When agents wait on a screening flow before they reach a lead, see "Power Dialer Overview".

When to Contact Support

If none of these explains the call, contact Trackdrive support with the call's id and the time of the call. Support can read the dialer's and the buyer's side of the call that your screens don't show.

Contact TrackDrive

Questions?

We're here to help. Reach out and a Voice Marketing Cloud Specialist will get back to you.

Email support@trackdrive.com
Request A Demo

Request A Demo.

See how you can improve your marketing and the customer experience with the Voice Marketing Cloud.

Request a demo